What is the clear space between the uprights? Looking at using a press break insert and need to know what length of tooling will fit onto the bed between the verticals.

28-3/4' is your inside width. Thanks for shopping with us Mike!

What is product availability looking like for 2022?

At the time of the question, these are in stock on 3/21/22. If the item can be added to your cart, it's in stock. Thanks for your question!

When will you have more air 50 ton ones in stock?

I'm going to be honest with you Jim; as of today, 10/28/21, the availability on these is awful. If you want one, and you want to get one from the next shipment, you should place a deposit on one and be prepared to wait however long it takes and pay whatever cost when they arrive. We cannot say when we'll get more or what they'll cost. Our shipping costs have risen 557% in the last year. When they come in, they sell out in days. I apologize that I don't have a better answer for you sir.

These need to be bolted to the floor or are they stable enough??

We have not found that bolting them to the floor is mandatory. They certainly don't vibrate during operation and walk across the shop. Granted, you have to use some common sense here. If you were to take an item very long and heavy, and press on it with a large portion of said item hanging off the front of the press, you should naturally expect the item's center of gravity to tip the press over. A lack of common sense will get you hurt with any piece of equipment, so please be careful when pressing with 100,000 pounds of force. Thanks Mike!

What is the warranty?

1 year 'parts warranty.' This means that if something breaks within a year of purchase, Redline will send you the part and the customer will install it. Please be aware it is not our policy to reimburse the customer for time spent installing the new part. We keep a pretty decent inventory of replacement parts on hand. Thanks Matt!

Move your mouse over image or click to enlarge

Norco 25 Ton Air/Hydraulic Shop Press $3,249.50

Norco 22 Ton Manual Hand Pump Shop Press $2,519.50

Redline 50 Ton Economy Air Hydraulic Shop Press with Winch $2,299.50

Norco 12 Ton Manual Hand Pump Shop Press $1,889.50

Redline 40 Ton Air Hydraulic Shop Press $1,699.50

Redline 30 Ton Air Hydraulic Shop Press

$1,649.50

Redline 50 Ton Air Hydraulic Shop Press

Model: RE50T-A

(5 reviews)

Optional Accessories

Include Rear Facing Guard ( +$174.95 )

Redline RE-AR 3/8" Air Hose Reel ( +$189.95 )

Pin Press Kit ( +$199.95 )

SMC 1/4" Lo-Flow Water Separator ( +$99.95 )

Extra Pair Of Press Plates ( +$299.50 )

U-Weld-It Metal Bending Finger Brake ( +$449.50 )

Include Rear Facing Guard

Redline RE-AR 3/8" Air Hose Reel

Pin Press Kit

SMC 1/4" Lo-Flow Water Separator

Extra Pair Of Press Plates

U-Weld-It Metal Bending Finger Brake

Brand

Redline Engineering

Type

Air over Hydraulic

Shipping upgrades offered in cart page

$2,999.50

This industrial Redline 50 ton hydraulic shop press is an air over hydraulic pressing machine perfect for manufacturing, auto repair, or general mechanical work. It features a pump capable of manual operation, as well as the ability to be powered via compressed air. Other standard features include a tonnage gauge, a winch that allows for easy raising and lowering of the press carriage, and a protective safety guard that reduces the possibility of an object flying out under pressure and hitting the operator. This press comes standard with 1 front facing grid guard and 1 set of press plates, but an additional rear facing guard as well as an extra set of press plates are also available for purchase. Order your new 100,000 pound capacity hydraulic shop press today from Redline Engineering!

KEY BENEFITS
• CE Certified
• 50 ton capacity
• Powder coated finish
• Air pedal is shielded for protection
• 36" movement of carriage up and down
• 8 height adjustments of 4.5" increments
• Carriage winch for easy carriage adjustment
• Ram cylinder capable of shifting both left and right
• Pressure gauge accurate +/- 2.5% of press capacity
• Welded shelves inside carriage to help support press plates

PRESS PLATE RATING
• Each press plate is rated to ½ the tonnage of the press; thus, if applying the press’ maximum force, the load must be distributed over both press plates to avoid damaging the press

• Hose length 50"
• Leg length 31.5"
• Cylinder stroke 7.8"
• Handle length 27-1/4"
• Air pump full stroke: 150s
• Main frame is 3.5" x 0.50"
• Inside frame width: 28-3/4"
• Cylinder ram diameter 2-3/4"
• Pump fluid volume: 81.1 fl oz.
• Manual full stroke: 126 pumps
• Interior carriage length:16-1/4"
• Internal cylinder diameter: 3.94"
• Operates at a 75dB sound rating
• Piston retraction time: 84 seconds
• Two heavy duty press plates 5" x 11"
• Air motor requires 7 CFM of air supply
• Pressure gauge accurate to +/- 2.5%
• Maximum pump pressure: 9050 PSI
• Overall dims 52.5" L x 31.5" W 73.5" H
• Cylinder piston/bore diameter: 3.93701"
• Interior carriage shelf-to-shelf width: 7-1/2"
• Middle carriage 35-3/4" W x9-1/4" D x 9-3/4" H
• Air pump full range without load: 165 seconds
• 10 inch cylinder shift left to right: 4-3/4" both ways
• Approximate number of pumps to full range without load: 126
• Work dims between cylinder and press plates:
-Min height from cylinder: 1-11/16"
-Max height from cylinder: 40"

• Download the manual pdf HERE

• Residential deliveries cost extra
• Ships to commercial location w/ forklift
• Units available in Pensacola, FL with rebate
• Pensacola, FL pickups – read our policies HERE
• Press with pallet ships @ 809 lbs. - 83" x 38" x 12" class 65
• Free shipping applies to $250 maximum. If shipping exceeds this amount a surcharge may be needed

Norco 25 Ton Air/Hydraulic Shop Press $3,249.50

Norco 22 Ton Manual Hand Pump Shop Press $2,519.50

Redline 50 Ton Economy Air Hydraulic Shop Press with Winch $2,299.50

Norco 12 Ton Manual Hand Pump Shop Press $1,889.50

Redline 40 Ton Air Hydraulic Shop Press $1,699.50

Redline 30 Ton Air Hydraulic Shop Press

$1,649.50

Reviews

4.8 / 5 (5 reviews)

Based on 5 Reviews Write review

Jeff Neises Feb 2, 2024

Good Quality
Feb 2, 2024

I am impressed. The table is stable and doesn't rock. The ram moves side to side easily yet isn't loose. The winch works good. I really cant find anything about it that I'm not fully satisfied with. And that's very rare for me. It came almost fully assembled so setup took less than an hour. The ram and the hose going to it was even pre filled so I didn't even have to bleed air or add oil. I am impressed. This is definitely not the typical "made in china" quality.
Christopher Cox Dec 26, 2023

Excellent press
Dec 26, 2023

Very solid and well designed piece of equipment with little frame spring at higher loads. Only issue I have found is that the hydraulic release is too low on the far right, slowing down release on production operations.
Devin W Aug 8, 2023

Solid buy.
Aug 8, 2023

Press is very well constructed, and functions exactly how you would expect, with plenty of power even before the tonnage limit. Nothing on it seems cheap with no corners cut. Shipping was a bit of a nightmare due to unforseen circumstances in the freight world, but Redline was quick to do everything in their power to get the machine to us intact and complete. Would absolutely do business again.

Ask & Answer

Eng Mike May 27, 2022

Q. What is the clear space between the uprights? Looking at using a press break insert and need to know what length of tooling will fit onto the bed between the verticals.
A. 28-3/4" is your inside width. Thanks for shopping with us Mike!
Matt Mar 10, 2022

Q. What is product availability looking like for 2022?
A. At the time of the question, these are in stock on 3/21/22. If the item can be added to your cart, it's in stock. Thanks for your question!
Jim Oct 27, 2021

Q. When will you have more air 50 ton ones in stock?
A. I'm going to be honest with you Jim; as of today, 10/28/21, the availability on these is awful. If you want one, and you want to get one from the next shipment, you should place a deposit on one and be prepared to wait however long it takes and pay whatever cost when they arrive. We cannot say when we'll get more or what they'll cost. Our shipping costs have risen 557% in the last year. When they come in, they sell out in days. I apologize that I don't have a better answer for you sir.
Mike Oct 18, 2021

Q. These need to be bolted to the floor or are they stable enough??
A. We have not found that bolting them to the floor is mandatory. They certainly don't vibrate during operation and walk across the shop. Granted, you have to use some common sense here. If you were to take an item very long and heavy, and press on it with a large portion of said item hanging off the front of the press, you should naturally expect the item's center of gravity to tip the press over. A lack of common sense will get you hurt with any piece of equipment, so please be careful when pressing with 100,000 pounds of force. Thanks Mike!
Matt Sep 08, 2021

Q. What is the warranty?
A. 1 year "parts warranty." This means that if something breaks within a year of purchase, Redline will send you the part and the customer will install it. Please be aware it is not our policy to reimburse the customer for time spent installing the new part. We keep a pretty decent inventory of replacement parts on hand. Thanks Matt!