Website Feedback


Add your email address to take a quick survey and receive $10.00 off your next order!


Redline 100 Ton Electric Hydraulic Shop Press

Model: RE100T-E

Optional Accessories

Include Rear Facing Guard

Pin Press Kit

10ft. Electrical Cord

Extra Pair Of Press Plates

U-Weld-It Metal Bending Finger Brake

Shipping upgrades offered in cart page



This industrial Redline 100 ton hydraulic shop press is an electric over hydraulic pressing machine perfect for manufacturing, auto repair, or general mechanical work. It features a powerful electric hydraulic pump for heavy duty pressing, a ram cylinder that can move left and right, and a crank style carriage winch for easy adjustment of the middle carriage. A tonnage gauge is mounted on top of the hydraulic fluid tank to see how much pressure you are currently using. For safety reasons a shop press safety guard is included that reduces the possibility of an object flying out under pressure and hitting the operator. Order your new 200,000 pound capacity hydraulic shop press today from Redline Engineering!

• CE Certified
• 100 ton capacity
• Powder coated finish
• 33" movement of carriage up and down
• 6 height adjustments of 5-1/2" increments
• Carriage winch for easy carriage height adjustment
• Ram cylinder capable of shifting both left and right
• Pressure gauge accurate +/- 2.5% of press capacity
• Electric powered hydraulic cylinder for heavy duty pressing
• Safety grate can be latched into place in multiple increments
• Welded shelves inside carriage to help support press plates
• Machine does not come with a power cord.  Customer will need to either hard-wire power to the machine or supply a power cord
• Pump does not come pre-filled with hydraulic fluid
• 7-8 gallons of ISO#32 or Shell#15 hydraulic fluid will be needed to operate the pump
• Long and/or thin extension cords are not recommended as amp loss could damage the motor

• Each press plate is rated to ½ the tonnage of the press; thus, if applying the press’ maximum force, the load must be distributed over both press plates to avoid damaging the press

Show more


• Leg length 39"
• 12"/minute feed rate
• Inside frame width: 31"
• Cylinder stroke 11.81"
• Base dims: 47-1/4" x 39"
• Interior carriage length: 16-3/4"
• Cylinder ram diameter 3-1/2"
• Winch cable diameter: 5/32"
• Main frame is 5-5/8" x 5/8"
• Press head to floor: 50-1/2"
• Carriage pin diameter: 2-1/16"
• Safety grate: 30-1/2" x 28-3/4"
• Diameter of cylinder bore 5.511"
• Piston retraction time: 39 seconds
• Pump VFR - .914 gallons per minute
• Distance between leg holes: 7-5/8"
• Pressure gauge accurate to +/- 2.5%
• Pump pressure 9,235 psi (63.7 Mpa)
• Overall dims 62-1/2" L x 39" W x 73" H
• Interior carriage shelf-to-shelf depth: 9"
• Cylinder piston/bore diameter: 5.51181"
• Middle carriage 13-3/8" L x 42-1/4" W x 13" H
• Press head to carriage (lowest position): 29-1/2"
• Two heavy duty press plates 13-3/4" L x 5-1/8" W x 6-5/8" H
• Work dims between cylinder and press plates:
-Min height from cylinder: 1-3/4"
-Max height from cylinder: 29-1/4"
• 60 Hz
• 110 V
• 1700 RPM
• 19.12 AMP
• 2 Hp electric motor



• Download the manual pdf HERE


• Ships 1716 lbs. at 85" x 49" x 23" (1 piece)
• Residential deliveries cost extra
• Ships to commercial location w/ forklift
• Units available in Pensacola, FL with rebate
• Pensacola, FL pickups – read our policies HERE
• Free shipping applies to $400 maximum. If shipping exceeds this amount a surcharge may be needed




Ask & Answer

  • Tim Sep 19, 2023
    Q. Can the complete cable assembly be ordered to where you just pull the shafts out, remove the old cable, and replace it with a new cable...No crimping etc?
    A. We stock these replacement CABLE KITS. We order them from the factory pre-made, so we have no experience with attempting to crimp any of these cables. I don’t doubt it’s plenty possible for a customer to create/modify this cable as needed and do his/her own crimping, but it’s nothing we at Redline offer or have experience. Thanks for shopping with us!
  • Joe Jun 13, 2022
    Q. My press “squeals” sometimes when under load.. ive looked it up and aeration could be likely cause.. how often should you bleed air from the system and do you do it the same way as you do when first using the press(run for 1 minute with the bleeder valve open)?
    A. Our tech is [email protected] and he can probably help you; but first, just humor us and add another gallon of hydraulic fluid to the reservoir and test it. 95% of the time the fluid is just a tad low. Thanks Joe!
  • Jonathan Jul 19, 2021
    Q. How many gallons does it take to operate?
    A. We recommend buying 2 x 5-gallon jugs of #32 hydraulic fluid. You won't use it all, but you'll use most of it to fill it full. It's cheaper than buying 1 big jug and then 3 small gallon jugs.


You need to be logged to vote.

  1. Home
  2. Shop Equipment
  3. Hydraulic Shop Press
  4. All Shop Presses
  5. Redline 100 Ton Electric Hydraulic Shop Press

Free shipping only applies to products that are marked "free shipping" or "ships free" in the title. Freight ship items have a predetermined max amount that can be spent under our free shipping policy. In the event you reside in an unusually high cost shipping zip code we may alert you that a shipping surcharge may be necessary.

Click OK to view our full shipping policy. Clicking cancel will keep you on the current page.

Search Cart Quote Facebook eBay YouTube Menu Menu