Best Parts Washers for Your Shop: How to Choose the Right Type

Last Updated on August 10, 2026

Every shop deals with grease, oil, and grime that need to be removed before you can inspect, measure, or reassemble a part. A parts washer takes that job off your plate and turns a slow, messy chore into a quick step in your workflow, rather than an afternoon lost to scrubbing. But parts washers are not all built the same way, and picking the wrong type can leave you frustrated instead of clean.
Some units use water-based cleaners, others use solvents. Some spray parts under heat and pressure, others let parts soak in a tank until the grime lifts on its own. Others are sized for a full transmission, others for a handful of small bolts and carburetor jets. This guide walks through the main types of parts washers, what each one does best, and where you can find them in Redline’s lineup. By the end, you should have a clear picture of which parts washer fits your shop, your budget, and the parts you clean most often.

What to Think About Before You Buy

Before you pick a parts washer, take a minute to think through how you will actually use it day to day. A few questions make the choice much easier.
  • What size are the parts you clean most often? Small bolts and carburetor jets need a different setup than full engine blocks or transmission housings.
  • How much grease, oil, or carbon buildup are you dealing with? Heavy buildup usually calls for heat and a stronger pump.
  • How often will the washer run? A shop that cleans parts every day needs something built for continuous use, not an occasional job.
  • How much floor space and power do you have? A benchtop unit fits where a full cabinet cannot, but it also holds less and cleans smaller batches.
Once you have honest answers to these questions, the type of washer you need becomes obvious. Most shops fall into one of the categories below.

Solvent vs Aqueous Parts Washers: What’s the Difference

Parts washers generally use one of two kinds of cleaning fluid: solvent or aqueous. Solvent-based washers use petroleum products to cut through grease fast, but they come with real downsides. They pose a fire risk; require careful ventilation, and have disposal rules for used solvents that vary by state.
Aqueous parts washers use a water-based degreaser instead. They cost less to run, produce fewer emissions, and eliminate the flammability risk associated with solvents. For this reason, Redline’s parts washers are all built around non-petroleum, aqueous-based cleaning fluid rather than solvent. Automotive degreaser works well in these units, and Redline recommends against using petroleum-based fluids, as they can cause the pump bushings to swell and lock up the motor over time.
For most shops doing general cleaning, an aqueous washer is the simpler and safer place to start.

Aqueous Sink Washers: The Everyday Workhorse

Redline RE20PW 20 Gallon Parts Washer CLEARANCE
Redline offers two solid aqueous sink-style washers, with the main difference being capacity. The Redline RE20PW 20 Gallon Parts Washer is an all-steel washer with a built-in drain, a 110V pump running at 50 gallons per hour, and an on/off switch with an indicator light. It holds 20 gallons of cleaner, works well for smaller shops or lighter daily use, and is currently priced as a clearance item.
For bigger jobs, the Redline 40 Gallon Parts Washer gives you double the tank capacity and a 200 lb load rating, so it can handle bulkier components without needing frequent refills. Both washers include a UL-listed pump and a powder coat finish, and both are simple enough that a new employee can start using one within minutes.

Heated Parts Washers: Best for Grease and Carbon Buildup

Redline 3 Gallon Heated Air Powered Parts Washer
Heat speeds up cleaning by loosening grease and carbon that cold cleaners struggle to break down on its own. If your shop deals with a lot of transmission grime, carbon deposits, or baked-on oil, a heated washer will save you real time on every job that comes through the door.
The Redline 3 Gallon Heated Air Powered Parts Washer uses compressed air to spray heated fluid inside an enclosed chamber, with the reservoir reaching up to 150 degrees Fahrenheit. It includes a vent fan on the back of the chamber, a fluid level indicator, an interior grate to catch small pieces as they come loose, and a fold-down control door that reveals the reservoir and tubing for easy access. Because it produces fumes from the cleaning agent, Redline recommends wearing an OSHA-approved respirator while it runs.
For shops that need heat on a much larger scale, the industrial cabinet shown next is also a heated model, built for much larger components and higher volume.

Industrial and Automatic Parts Washer Cabinets

Redline 500HWC Heated Heavy Duty Industrial Parts Washer Cabinet
When you are cleaning full engines, transmissions, or other heavy components, a small sink or benchtop unit will not cut it. This is where an industrial parts washer earns its keep, and where automation starts to matter.
The Redline 500HWC Heated Heavy Duty Industrial Parts Washer Cabinet is built to wash components up to 500 lbs. It runs on a 220V, 2HP motor, spins parts on a rotating turntable, and sprays hot water-soluble degreaser through 18 replacement nozzles at 35 to 37 psi and 52.8 gallons per minute. Set the timer and temperature between 120 and 150 degrees Fahrenheit, and the machine handles the rest on its own, shutting down and cooling as needed to prevent overheating. A rotating skimmer disk keeps the wash fluid cleaner for longer by pulling floating grease and oil off the surface and into a grease bucket. At $5,999.50, it is a serious investment, but for shops that rebuild engines or transmissions regularly, it pays for itself in labour saved over time.

Custom Parts Washer Setups

Not every job fits neatly inside a standard rack or basin, and this is where building a custom setup makes a real difference. The 500HWC’s interior parts tree is both customizable and removable, so you can reconfigure it around whatever you are washing that day, whether that means a large cylinder head hung from the center pole or a batch of smaller components arranged on the included parts tray.
Redline also sells accessories separately, including spray guns, flex hoses, replacement pumps, and detergent, so you can build a washer setup that matches your shop’s specific workflow rather than settling for a one-size-fits-all configuration. Over time, this lets you adjust your setup as your work changes without replacing the whole machine.

Benchtop and Small Parts Washers

If floor space is tight or you mainly clean smaller components, a full-size cabinet is more than you need. The Redline 3 Gallon Air Powered Benchtop Parts Washer gives you the same enclosed spray-chamber design as the heated model above, minus the heat, in a compact footprint that sits right on a workbench. It runs on 70 to 120 psi of shop air, includes an interior grate and screen filter to catch debris, and comes with a light built into the chamber so you can see what you are doing during longer jobs.
This is a good fit for shops that regularly clean carburetors, small brackets, or hand tools and do not need the size or cost of a full industrial cabinet.​

What About Ultrasonic Parts Washers?

Ultrasonic parts washers use sound waves to shake dirt and grime loose from a part submerged in cleaning solution. They work well for small, precision components like carburetor jets, fuel injectors, and fine mechanical parts, since sound waves reach tight passages and hidden corners that a spray nozzle or soak tank might miss. If your shop often handles this kind of detail work, it is worth checking Redline’s current parts washer selection to see what fits alongside the units covered here.

Keeping Your Parts Washer Running Longer

Whatever type you choose, a little upkeep goes a long way. Pre-scrape heavy deposits before washing to extend the life of your cleaning solution. Check and replace filters regularly so the pump does not have to work harder than it should. Dispose of used cleaning solution according to your local regulations, and avoid washing parts with sensitive seals with solvents or hot water, as this could damage them. These habits protect your investment and keep cleaning times consistent, no matter which washer you choose.

So, Which Parts Washer Is Right for Your Shop?

There is no single washer that works best for every shop, but matching the type to your work makes the decision simple.
  • Small precision parts and tight budgets point toward a benchtop or aqueous sink washer.
  • Heavy grease, oil, and carbon buildup call for a heated model.
  • Full engines, transmissions, or other large components need a cabinet built for that scale, like the 500HWC.
  • Shops running several job types at once often end up with more than one washer to cover the full range of work.
Take a look at Redline’s full lineup of parts washers to compare options side by side, or reach out to the team for help picking the right setup for your shop.

Leave a Reply

Your email address will not be published. Required fields are marked *