Website Feedback

Email:

Add your email address to take a quick survey and receive $10.00 off your next order!

0

Redline 50 Ton Electric Hydraulic Shop Press

Model: RE50T-E

(1 review)

Optional Accessories


Include Rear Facing Guard


Pin Press Kit


10ft. Electrical Cord


Extra Pair Of Press Plates


U-Weld-It Metal Bending Finger Brake


10 gallons #32 hydraulic fluid
Brand
Type

Shipping upgrades offered in cart page

$5,999.50

Description

This industrial Redline 50 ton hydraulic shop press is an electric over hydraulic pressing machine perfect for manufacturing, auto repair, or general mechanical work. It features a electric powered hydraulic pump for heavy duty pressing, a safety guard with multiple increments, and a crank style carriage winch for easy adjustment of the middle carriage. On top of the hydraulic fluid tank is a tonnage gauge to inform you of how much pressure you are currently using. Order your new 100,000 pound capacity hydraulic shop press today from Redline Engineering!
 

KEY BENEFITS
• CE Certified
• 50 ton capacity
• Powder coated finish
• Ram moves 2" in 5 seconds
• 44" movement of carriage up and down
• 8 height adjustments of 5-1/2" increments
• Carriage winch for easy carriage height adjustment
• Ram cylinder capable of shifting both left and right
• Pressure gauge accurate +/- 2.5% of press capacity
• Electric powered hydraulic cylinder for heavy duty pressing
• Safety grate can be latched into place in multiple increments
• Welded shelves inside carriage to help support press plates
• Machine does not come with a power cord.  Customer will need to either hard-wire power to the machine or supply a power cord
IMPORTANT NOTES
• Pump does not come pre-filled with hydraulic fluid
• 7-8 gallons of ISO#32 or Shell#15 hydraulic fluid will be needed to operate the pump
• Long and/or thin extension cords are not recommended as amp loss could damage the motor
 

PRESS PLATE RATING
• Each press plate is rated to ½ the tonnage of the press; thus, if applying the press’ maximum force, the load must be distributed over both press plates to avoid damaging the press

Show more

Specs

• Leg length 31-1/2"
• Cylinder stroke 8.15"
• Ram diameter 100mm
• Inside frame width: 28-3/4"
• Winch cable diameter: 5/32"
• Main frame is 3-1/2" x 1/2"
• Cylinder ram diameter 2-1/2"
• Carriage pin diameter: 1-3/16"
• Safety grate: 24-3/8" x 26-1/2"
• Inside carriage width: 7-1/2"
• Interior carriage length:16-1/4
• Full travel time: 20 seconds
• Piston retraction time: 26 seconds
• Pump VFR - .914 gallons per minute
• Maximum pump pressure 9,000 psi
• Pressure gauge accurate to +/- 2.5%
• Overall dims 62" L x 31-1/2" W x 72" H
• Cylinder piston/bore diameter: 3.937"
• Inside carriage shelf-to-shelf depth: 7-1/4"
• Middle carriage 35-7/8" L x 10-3/16" W x 9-13/16" H
• Two heavy duty press plates 10-15/16" L x 5-1/8" W x 1-3/8" thickness
• Work dims between cylinder and press plates:
-Min height from cylinder: 1-11/16"
-Max height from cylinder: 40"

ELECTRIC MOTOR
• 60 Hz
• 110 V
• 1700 RPM
• 19.12 AMP
• 2 Hp electric motor

Downloads

• Download the manual pdf HERE

Shipping

• Ships 949 lbs. at 83" x 38" x 20"
• Residential deliveries cost extra
• Ships to commercial location w/ forklift
• Units available in Pensacola, FL with rebate
• Pensacola, FL pickups – read our policies HERE
• Free shipping applies to $350 maximum. If shipping exceeds this amount a surcharge may be needed

 

Videos

Reviews

5.0 / 5 (1 review)
Based on 1 review Write review
  • Chris Behnken May 23, 2020

    Badass!

    May 23, 2020
    This unit is badass, we run a drivetrain and manual transmission rebuilding service @ rvenge performance and a air over hydraulic press was just slowing us down too much. This thing is 8 times faster than our air/hydro 40 ton unit we had before and it really speeds up work. Sets up easily, few parts to really install. You may want a friend when putting it upright, we just used an engine hoist and heavy strap to pick it up by the upper header and it was really easy. Just be careful, its about 900 lbs. To put the power unit on we just used a jack to get it close and it was also really easy. Our unit only took about 5 gallons of aw32 just FYI, you may only need one bucket. Very well built, quiet (no more need for ear muffs like the air one needed), fast, and doesn't deflect at all. Redline also ships very fast. We ordered on a Monday and had it here and setup on a Friday. Presses with all the features this one has were double the cost. Thanks Redline!

Ask & Answer

  • dave Feb 02, 2024
    Q. Good morning, I really liked your shop press, it seems to be faster than other brands and the one that is most worth buying. I need two like this. But the 110v amperage is a little high for our capacity. Can you do it in 220v?
    A. We can, but we'd have to special order this press for you with a 220V motor. Lead time would be about 4-5 months. Let us know if you wish to proceed. Thanks Dave.
  • Himani Jan 12, 2024
    Q. IF WE WANT A MODIFICATION TO THIS PRESS DESIGN IS IT POSSIBLE, DO GUYS HAVE PEOPLE WHO CAN MODIFY THE PRESS CONSTRUCTION AS PER OUR REQUIREMENT? HOW MUCH DENSITY 50 TON PRESS CAN ACHIEVE?
    A. No sir. I'm sorry but we do not offer any custom work. You would need to modify the press to your liking yourself. Thank you for your question.
  • HK LEE Jan 09, 2024
    Q. I would like to know about dimensions for press plates if the specially made plates are applicable to this press unit.
    A. I looked in the specs tab and found, "Two heavy duty press plates 10-15/16" L x 5-1/8" W x 1-3/8" thickness." I then went to our PRESS PLATE LISTING and found the overall dimensions of the 50T plates to be 11-1/8" L x 5-1/2" W x 5-1/4" H. I realize these dims vary slightly. The factory probably changed them at some point by a tiny amount and didn’t alert us. Thanks for shopping with us!
  • Jack Nov 13, 2023
    Q. Good Afternoon,
    I have a RE50T-E press. We would like to purchase the rear guard, but I am struggling to find the part number. Would you kindly share the part number and I can order it form the website?
    A. Sure, I believe you’re looking for THIS sir. Thanks for shopping with us!
  • welderman Oct 07, 2022
    Q. Does the Redline or the Norco 50 ton electric over hyd press have manual pumping or a slow mode for setting preload on bearings ?
    A. No sir. Neither of these presses have the feature you're looking for. If you need a press that will very carefully build pressure, you might consider our RE50T-A. It doesn’t build pressure near as fast as the electric version. Thanks Jason!

ASK A “PUBLICLY POSTED” QUESTION

You need to be logged to vote.



  1. Home
  2. Copy Category
  3. Medium Duty
  4. Redline 50 Ton Electric Hydraulic Shop Press

Free shipping only applies to products that are marked "free shipping" or "ships free" in the title. Freight ship items have a predetermined max amount that can be spent under our free shipping policy. In the event you reside in an unusually high cost shipping zip code we may alert you that a shipping surcharge may be necessary.

Click OK to view our full shipping policy. Clicking cancel will keep you on the current page.

Search Cart Quote Facebook eBay YouTube Menu Menu